纳秒脉冲表面介质阻挡放电激励改善飞翼力矩特性的实验研究

针对飞翼布局力矩控制问题,采用纳秒脉冲表面介质阻挡放电（NS-DBD）激励,在来流风速30 m/s时,开展飞翼等离子体流动控制风洞试验,研究了不同激励参数和位置对飞翼升阻特性和力矩特性的影响。结果表明,NS-DBD激励能够有效改善飞翼大迎角气动特性。激励频率对飞翼升阻特性影响较大,激励频率为0.2 kHz时,增升效果最好,最大升力系数提高14.5%,失速迎角推迟5°。随着激励频率的增加,增升效果逐渐变差,减阻效果变好。单侧施加激励时,能够实现大迎角下飞翼模型的力矩控制,随着激励频率的增加,滚转力矩的控制效果减小,激励频率为0.2kHz时,平均滚转力矩系数变化为ΔMX=0.005691;偏航力矩的控制效果增大,激励频率为1kHz时,平均偏航力矩系数变化为ΔMY=-0.001571;俯仰力矩的控制效果减小,激励频率为0.2kHz时,平均俯仰力矩系数变化为ΔMZ=-0.002576。在中翼段和内翼段施加激励,破坏了飞翼的俯仰力矩特性,在外翼段和机翼右侧施加激励,能够显著改善飞翼的俯仰力矩特性。流场测量结果表明：等离子体激励对飞翼气动力矩的控制,主要是通过控制流动分离和控制横向流动来实现的。NS-DBD激励为改善飞翼布局稳定性和操纵性提供一种潜在的技术手段。     

Flow separation control on swept wing with nanosecond pulse driven DBD plasma actuators

A 15° swept wing with dielectric barrier discharge plasma actuator is designed.Experimental study of flow separation control with nanosecond pulsed plasma actuation is performed at flow velocity up to 40 m/s. The effects of the actuation frequency and voltage on the aerodynamic performance of the swept wing are evaluated by the balanced force and pressure measurements in the wind tunnel. At last, the performances on separation flow control of the three types of actuators with plane and saw-toothed exposed electrodes are compared. The optimal actuation frequency for the flow separation control on the swept wing is detected, namely the reduced frequency is 0.775, which is different from 2-D airfoil separation control. There exists a threshold voltage for the low swept wing flow control. Before the threshold voltage, as the actuation voltage increases, the control effects become better. The maximum lift is increased by 23.1% with the drag decreased by 22.4% at 14°, compared with the base line. However, the best effects are obtained on actuator with plane exposed electrode in the low-speed experiment and the abilities of saw-toothed actuators are expected to be verified under high-speed conditions.     

民机飞行结冰参数的模拟与校准

结冰问题的研究对于民用飞机设计十分重要,采用结冰风洞试验是主要的方法之一,欧美国家有很多成熟的结冰风洞用于型号研究。结冰风洞中需要对很多参数进行控制,其中水雾参数精确控制的难度很大,而且一般通过间接方法来进行测试校准,往往误差较大,导致不同结冰风洞试验结果往往有所差异。文章介绍了在意大利宇航中心的IWT 结冰风洞完成的冰风洞校准试验,对结冰风洞水雾参数校准方法进行了阐述,为民机结冰风洞研究提供参考。     

Numerical investigation of flow mechanisms of tandem impeller inside a centrifugal compressor

This study numerically investigated a single stage centrifugal compressor ‘‘Radiver’’ with a wedge diffuser and several tandem-designed impellers to explore the flow phenomena within the tandem impeller and the potential to enhance compressor performance. The results demonstrate that tandem design and clocking fraction (λ_s) significantly affects the compressor performance. The compressor stage with tandem impellers of Series A of boundary layer growth interruption alone are observed to have a widely operating range but efficiency and total pressure ratio penalty compared with that of conventional impeller. The tandem impeller with at least the same impeller efficiency as the conventional design is considered as a critical design criteria so that further modification process based on the flow characteristic of tandem impeller is necessary. In order to restrain the inducer wake and exducer shock losses, parameters modification of blade angle and thickness distributions are necessary and the modified tandem impeller of Series B is obtained. The modified tandem impeller with 25% clocking arrangement shows an 8.45% stall margin increase and maintains the total pressure ratio and efficiency as the conventional design, which proves the potential of tandem impeller to improve compressor stage performance. It is noteworthy that the tandem impellers of Radiver have not shown obviously balanced exit flow field and the fundamental mechanism of stall margin extending of tandem impeller lies on the improved impeller/diffuser matching performance resulting from the incidence angle variation at diffuser inlet.     

Streamwise vortex generation by the rod

The technology development related to aerodynamics is leading to ever increasing loads of wings, airfoils and turbine and compressor blades. The increase in aerodynamic forces is often leading to flow separation and depreciation of the aerodynamic performance of flying objects or propulsion systems. Flow control methods are required to avoid these negative effects. In the recent two decades the flow control by means of air-jet vortex generators has been also intensively investigated. In this method a streamwise vortex is introduced by an oblique jet. The necessity to supply air by a pipe system may be considered a disadvantage. In order to eliminate this feature, it has been proposed to put out a rod instead of a jet. It has been shown that the application of a rod can introduce the same effect as a jet, as long as the streamwise vortex generation is concerned and appropriate dimensions are used. The present paper focuses on the influence of rod vortex generators on a flow pattern downstream. The results presented here concern experimental and numerical investigations and provide guidelines for the design of a new flow control method dedicated mainly to external flows.     

A CFD-based numerical virtual flight simulator and its application in control law design of a maneuverable missile model

A CFD-based Numerical Virtual Flight (NVF) simulator is presented, which integrates an unsteady flow solver on moving hybrid grids, a Rigid-Body Dynamics (RBD) solver and a module of the Flight Control System (FCS). A technique of dynamic hybrid grids is developed to control the active control surfaces with body morphing, with a technique of parallel unstructured dynamic overlapping grids generating proper moving grids over the deflecting control surfaces (e.g. the afterbody rudders of a missile). For the flow/kinematic coupled problems, the 6 Degree-Of-Freedom (DOF) equations are solved by an explicit or implicit method coupled with the URANS CFD solver. The module of the control law is explicitly coupled into the NVF simulator and then improved by the simulation of the pitching maneuver process of a maneuverable missile model. A nonlinear dynamic inversion method is then implemented to design the control law for the pitching process of the maneuverable missile model. Simulations and analysis of the pitching maneuver process are carried out by the NVF simulator to improve the flight control law. Higher control response performance is obtained by adjusting the gain factors and adding an integrator into the control loop.     

Electrochemical trepanning with uniform electrolyte flow around the entire blade profile

In the traditional machining process for diffusers, blades are easily deformed, and methods suffer from high tool wear and low efficiency. Electrochemical machining(ECM) possesses unique advantages when applied to these difficult-to-machine materials. In the ECM process, theflow field plays a crucial role. Here, an electrolyte flow mode that supplies uniform flow around the entire blade profile was adopted for electrochemical trepanning of diffusers. Various flow rates were employed to obtain the optimal flow field. Simulations were conducted using ANSYS software, and results indicated that increasing the flow rate substantially afforded a more uniform flowfield. A series of experiments was then performed, and results revealed that increasing the flow rate greatly improved both the machining efficiency and the surface quality of the diffusers. The maximum feeding rate of the cathode reached 4 mm/min, the blade taper of the concave part decreased to 0.02, and the blade roughness was reduced to 1.216 lm. The results of this study demonstrated the high feasibility of this method and its potential for machining other complex components for engineering applications.     

点阵结构空气舵及内部流体热流固耦合研究

开展了钛合金TC4材料激光粉末床熔融(LPBF)工艺研究,在此基础上设计了多孔轻质空气舵模型,并基于有限差分法(FDM),采用三维流固耦合共轭传热数值计算方法,利用流体体积法(VOF)追踪流体自由液面,研究了典型的点阵夹层结构的空气舵内部冷却液动态换热过程的相互影响过程,考虑了冷却液与钛合金材料蒙皮间的耦合传热及湍流换热。结果表明,空气舵的内部流体压强随速度的增加而增加,从而导致流体出口的速度增加。当压强增加到一定程度时,流体的出口以水柱形式喷出。虽然较大的流体速度可以带走较多的热量,但是影响远小于对压强的影响。综合考虑空气舵的服役要求,获得了合适的冷却水入口速度。     

Capillary flow rate limitation in asymmetry open channel

This paper focuses on the stability of capillary forced flow.In space,open capillary channels are widely used as the liquid and gas separation devices to manage liquid positioning and transportation.Surface collapse happens when the flow rate exceeds the critical value,leading to a failure of propellant management.Knowledge of flow rate limitation is of great significance in design and optimization of propellant management devices(PMDs).However,the capillary flow rate limitation in an asymmetry channel has not been studied yet in the literature.In this paper,by introducing an equivalent angle to convert the asymmetry corner to a symmetry one,the one-dimensional theoretical model is developed.The flow rate limitation can then be investigated as a function of the channel geometry as well as liquid property based on the model.Comparisons between the asymmetry and symmetry channels bring forth the characteristics of the two kinds of channels,and demonstrate good accordance between the new advanced model and the existing one in the literature.This theoretical model can provide valuable reference for PMD designers.     

加筋壁板VARI整体成型工艺设计与验证术

针对一种典型复合材料加筋壁板,完成模具结构及工艺流程等整体成型工艺设计,同时利用PAM-RTM软件完成流道设计优化模拟,并根据模拟结果选择合理的注射方式及流道布局,最终根据所选方案完成工艺试验验证,对构件进行超声无损检测,检测结果显示构件没有内部缺陷、树脂充分填充,最终验证了加筋壁板整体成型工艺设计及模拟分析的有效性.